Steel N690 in cutlery: uses and limits

N690 steel is a balanced stainless steel for cutlery. It resists corrosion well, accepts a usable hardness around 59 to 61 HRC depending on the treatment, and can be reshaped without laboratory equipment. It is not the hardest steel on the market, nor the toughest, nor the easiest to polish at home. It is a compromise, and that is precisely what makes it interesting for a knife intended for use.

Produced by the Austrian steelmaker Böhler, N690 is a martensitic stainless steel with a high carbon content, with the addition of cobalt that creates much discussion. We will see below what this cobalt really changes, and especially what it does not change.

In the workshop, this steel is notably used in theAsmo D, a friction folding knife designed for the pocket and everyday use. This page explains why this choice is solid, and in which cases another steel would be more appropriate.

What is N690 steel?

N690 belongs to the family of martensitic stainless steels: stainless steels capable of being hardened by quenching, unlike the stainless steels used for pots and sinks. Its material designation is 1.4528, its European designation X105CrCoMo18-2. Behind these codes is a formula: about 1.08% carbon, 17.30% chromium, 1.10% molybdenum, 0.10% vanadium, and 1.50% cobalt.

Carbon provides hardness. Chromium ensures corrosion resistance and forms carbides that contribute to wear resistance. Molybdenum and vanadium refine the overall behavior. Cobalt, for its part, deserves its own section.

Böhler presents N690 as a corrosion-resistant steel, suitable for polishing, with good toughness and high wear resistance. The manufacturer also states that it is approved for contact with food and beverages. It can indeed be found in the food industry, on machine knives, long before arriving on our workbenches.

A clarification that avoids disappointments: stainless does not mean imperishable. Stainless steel resists oxidation better than carbon steel, it is not immune to it. An N690 blade left wet in a leather sheath, or stored dirty after a citrus session, can develop marks. The difference with carbon steel lies in the tolerance to neglect, not in its elimination. To place the two families, the comparison Stainless or carbon steel details what each one asks for on a daily basis.

What cobalt changes, and what it does not change

Cobalt is the favorite marketing argument of the N690. You read everywhere that it would make steel tougher, harder, more resistant, more everything. Let's look at what sources allow us to assert.

What is established: N690 contains approximately 1.50% cobalt, and Böhler lists it as a characteristic alloying element of the grade, alongside molybdenum and vanadium. In metallurgy, cobalt does not form its own carbides: it remains dissolved in the steel matrix. It therefore does not create additional hard particles as vanadium would.

What is not established: the manufacturer's datasheet does not assign any quantified, isolated, and measurable effect of cobalt on the toughness or edge retention of N690. Claims such as 'cobalt prevents the blade from becoming brittle' circulate without any verifiable protocol behind them. Caution, therefore.

Chrome, carbon, a bit of cobalt. No magic. Cobalt does not replace a controlled heat treatment or a blade geometry suited to the use, and it does not make the blade invulnerable to corrosion. N690 is a good steel overall, not because of a miraculous ingredient.

Hardness, corrosion, and edge retention

Three concepts that are often confused, and which deserve to be separated.

Hardness, measured in HRC, indicates the metal's resistance to penetration. The Böhler datasheet states 59 to 61 HRC under the test conditions specified by the manufacturer. This is a laboratory range, not a guarantee engraved on each knife: the actual hardness of a blade depends on the heat treatment cycle it has actually undergone. High hardness allows for a fine and stable edge, but by itself, it says nothing about the overall performance of the blade.

Corrosion resistance mainly depends on the chromium available in the matrix. With its 17.30% chromium, the N690 is in the comfortable range for knife stainless steels. Comfortable, not invincible: salt, acids, and stagnant moisture remain adversaries. Wiping after use is enough to keep the blade in good condition. Simple does not mean optional.

Edge retention It results from a combination: hardness, carbides present in the steel, but also and above all the geometry of the blade and the sharpening angle. A fine grind with a consistent angle cuts longer than a thick blade with a blunt edge, given the same steel. That is why no universal duration before resharpening can be honestly announced: it depends on what you cut, on what surface, and on the blade itself.

Heat treatment matters more than the name engraved on the blade

The Böhler sheet provides a framework: austenitizing between 1,030 and 1,080 °C, tempering between 100 and 200 °C. This framework is not a cooking recipe to be followed blindly. The actual cycle depends on the blade's cross-section, the practitioner's equipment, and the desired result: prioritizing maximum hardness, edge stability, or a compromise between the two.

Temperatures, holding time, cooling rate, number of temperings: each parameter alters the final structure of the metal. That is why an HRC value only makes sense when linked to an actual and measured protocol. Two blades cut from the same N690 bar can behave very differently depending on the hand that hardened them.

The practical consequence is simple: a reputed steel can produce a mediocre knife if it is poorly treated, and a modest steel, if well treated, can be surprising. The name of the steel speaks for itself. The treatment and geometry, however, do the work. The page dedicated to the manufacture of a handcrafted knife shows where this step fits into the life of a blade.

For which knives is N690 relevant?

Folding knives and pocket knives

This is the area where N690 is most naturally justified. A pocket knife lives in an ungrateful environment: sweat, humidity, dust, forgotten wiping after a snack. A properly treated stainless steel endures what a carbon steel would forgive less.

The N690 brings a useful balance: sufficient hardness for a daily stable edge, corrosion resistance that tolerates pocket life, and sharpening that remains accessible on standard stones. For a utility folding knife, intended for bread, sausage, string, and cardboard, it is a coherent profile.

This is exactly the reasoning behind the Asmo D: a friction folder meant to be used, not displayed. The archived variants of the model show the versions already made in N690.

Kitchen knives

On paper, the N690 checks useful boxes in the kitchen: constant contact with water and food, and a food contact suitability documented by the manufacturer. Maintenance remains reasonable: wash, dry, store in a dry place.

The fact remains that the name of the steel does not make a good kitchen knife. On a kitchen blade, the finesse of the grind and the edge profile weigh more in the result than the choice between two comparable stainless steels. An N690 mounted on a thick geometry will disappoint compared to a lower-rated steel mounted thin. Other stainless steels can also be preferred depending on the intended use: N690 is not automatically the best candidate for a very fine kitchen blade, and it would be dishonest to claim otherwise.

Fixed knives and outdoor uses

For a general-purpose fixed outdoor knife, N690 can hold its own, especially in a humid environment. However, no serious public data allows it to be presented as suitable for repeated impacts, levering, or batonning. A knife is in any case not a crowbar, regardless of the steel. For these extreme uses, other families of steels and especially other geometries deserve consideration.

Sharpening and maintaining an N690 blade

Good news: N690 requires nothing exotic. A few habits are enough.

  • Clean the blade after use, especially after acidic or salty foods.
  • Dry before storing. A damp case is the best friend of corrosion.
  • Avoid prolonged storage in humid conditions, including leather.
  • Maintain the thread regularly, before it becomes completely dull: a few passes are enough then, compared to a full session if you wait too long.
  • Use a suitable stone or abrasive. Standard water stones are suitable; diamond can speed up the work, without being essential.
  • Maintain a consistent angle. Consistency matters more than the equipment.

Clearly distinguish between two operations: maintaining the edge, a short and frequent gesture, and full sharpening, which restores the edge in depth. The first postpones the second. The maintenance guide for artisanal knives details the gestures, stone in hand.

N690, 14C28N, 1.4116 or RWL34: how to locate them?

Comparing steels in absolute terms is a tricky exercise: heat treatment and geometry obscure all simple hierarchies. The table below provides general trends, to be read as guidelines, not as a ranking.

General trends of four stainless steels for cutlery, with appropriate heat treatment
Steel General trend Ease of maintenance Ease of sharpening Consistent use
N690 Balanced compromise between hardness, wear resistance, and corrosion High Moderate, accessible on standard stones Everyday folding knives, general kitchen knives
14C28N Stainless steel known for the fineness of edge it can accept High Generally simpler Fine kitchen blades and lightweight folding knives, depending on treatment
1.4116 Common stainless steel, generally lower hardness High Generally simpler Knives tolerant of reduced maintenance, domestic use
RWL34 Powder metallurgy stainless steel, high potential for hardness and finish High Depends heavily on the treatment and the targeted hardness Carefully made parts where finish and edge stability are paramount

None of these grades overshadows the others in all situations. The right choice depends on the intended use, the blade geometry, the level of maintenance you are willing to accept, the heat treatment method applied, and the price consistent with the overall knife. Steel should serve the knife. Not the other way around. To expand the thinking beyond these four grades, the guide which steel to choose for a knife lays out the complete method.

Why use N690 at FL Toussaint?

In the workshop, the N690 equips the Asmo D, a friction folding knife whose pivot screw allows adjustment of the opening friction. The choice of this steel corresponds to the use of the model: a pocket folding knife, often taken out, sometimes wiped, which must tolerate ambient humidity without requiring a maintenance ritual.

In my use, I look for a stable edge on this type of piece for everyday use and a re-sharpening that the owner can carry out themselves, on their own stones. The N690 meets these specifications without trendy steel or unjustified extra cost. This workshop feedback does not replace a standardized measurement: it simply reflects what I observe on the pieces that I make and use.

The already manufactured variants of the Asmo D are visible in the workshop's creations. Some of the displayed pieces may be sold; the others document the model. If no piece is available at the time of your visit, the model page allows you to register for the next series.

Key points about the N690

The N690 is a balanced martensitic stainless steel: comfortable corrosion resistance, usable hardness around 59 to 61 HRC according to the protocol, accessible re-sharpening. Its cobalt is a compositional element, not a special power. Its limits are those of any stainless steel in its category: it will mark if truly neglected, and it does not turn a bad geometry into a good blade.

For a utility knife, carried in a pocket or placed on the table, it is the right choice. The N690 knives currently offered and the archives of the Asmo D model show what this steel produces, once treated, ground, and assembled in the workshop.

Technical sources

  • Official datasheet BÖHLER N690 (1.4528 / X105CrCoMo18-2), voestalpine BÖHLER Edelstahl GmbH & Co KG: composition, heat treatment ranges, advertised hardness.
  • BÖHLER N690 product page, voestalpine BÖHLER Edelstahl: characterization of the grade and approval for contact with food and beverages.

Frequently asked questions

Is N690 a good steel for a knife?
Yes, for a utility knife: it is a stainless steel balanced between corrosion resistance, usable hardness and accessible resharpening. It does not dominate any category but has no crippling weak points. Its final quality, however, depends on the heat treatment applied and the geometry of the blade: the same steel can give a remarkable or disappointing knife depending on the work carried out.
Is N690 really stainless?
It is stainless in the sense of cutlery steel: its 17.30% chromium gives it comfortable corrosion resistance on a daily basis. It is not unalterable however. Prolonged exposure to salt, acids or stagnant humidity can scar it. Wiping after use and storing it in a dry place is enough to keep it healthy.
What is cobalt used for in N690?
Cobalt, present at approximately 1.50%, is a matrix element: it does not form its own carbides and remains dissolved in the steel. The manufacturer's information sheet does not attribute any isolated numerical effect to it, and the virtues that are often attributed to it online are not based on verifiable protocols. It is part of the overall recipe of N690, with no demonstrated miraculous role.
How hard can N690 reach?
The Böhler sheet announces 59 to 61 HRC under the manufacturer's test conditions, with austenitization between 1030 and 1080°C and tempering between 100 and 200°C. This range describes the potential of the steel, not the hardness of each knife: the real value of a blade depends on the thermal cycle it has actually undergone and can only be announced after measurement.
Is N690 difficult to sharpen?
No, it remains in the reasonable zone. Its high wear resistance requires a little more patience than softer stainless steel, but classic water stones are sufficient; the diamond speeds up the work without being obligatory. The decisive point is the regularity of the angle and the frequency: maintaining the wire often avoids complete resharpening, which takes time whatever the steel.
Is the N690 suitable for a folding knife?
It's even one of its best grounds. A folder lives in a pocket, exposed to humidity and perspiration, often stored without wiping. The corrosion resistance of N690 tolerates this regime, and its hardness allows a stable wire for everyday use. This is the reason why the Asmo D, workshop friction folding, is made of this steel.
Is N690 suitable for a kitchen knife?
Yes for general cooking: it supports contact with water and food, and Böhler documents its approval for food contact. On the other hand, on a kitchen blade, the fineness of the grind weighs more than the name of the steel. A thick-mounted N690 will cut less well than a comparable thin-mounted stainless steel, and other grades may be preferred for very thin blades.
What is the difference between N690, 14C28N and RWL34?
Three stainless steel, three profiles. The N690 aims for the compromise of use between corrosion, hardness and sharpening. The 14C28N is known for the fineness of wire it accepts and its generally easier sharpening. RWL34, from powder metallurgy, offers high hardness and finish potential, at the cost of more demanding work. None outperforms the others everywhere: use, geometry and heat treatment decide.
Back to top