One-off or small series: which knife should you choose?

One-off piece or small series: the question comes up often at the workshop, and the honest answer fits in one sentence. Neither option is better in every situation. A small series concentrates the work on a proven model and spreads preparation across several knives, which keeps the price more contained. A one-off piece opens up the design, materials and finishes, at the cost of manufacturing time borne by that knife alone. The right choice therefore depends on the intended use, budget, desired materials and expected level of finish. This guide explains what really changes in production, what accounts for the price differences, and how to decide without buying more than you need — or aiming too low.

Small series and one-off pieces: two ways of making a knife

The distinction is not simply a matter of quantity. It concerns the way I design, prepare and make the knife. In a small series, I work from a model whose design, geometry and settings have already been validated. Operations are repeated from one piece to the next, components are prepared together, and a limited number of material or finish variants are planned in advance.

For a one-off piece, everything starts from a blank sheet, or almost. A specific design, preparation dedicated to that single piece, sometimes unusual materials, and finishing time with no equivalent in a series. Every decision serves only one knife.

There is no universal threshold at which production becomes one or the other. What matters is how the work is organised — and what that organisation makes possible.

What is a handmade knife made in a small series?

A small series is based on a permanent or recurring model. The prototype has been designed, tested and corrected. The templates exist. The settings are known. When I launch a batch, I prepare the components for several knives at the same time: blades together, liners together, handles together. Each tooling change serves several pieces instead of just one.

This controlled repetition has two effects. First, the consistency I am looking for: knives from the same series resemble one another, are adjusted in the same way and age in a comparable way. Second, a more contained price, because preparation time is spread over the batch. To understand the manufacturing process in detail, there is a dedicated page.

Fitting, assembly and inspection remain individual operations. Every knife passes through my hands before it leaves. Series production organises the preparation; it does not replace piece-by-piece work.

This is the principle behind limited series and drops: a coherent batch is announced, made, then sold out. The Hack N Slash works this way — you can discover the Hack N Slash to see what this format looks like when applied to a specific model.

What is a one-off piece?

A one-off piece gives me what a series cannot: freedom. Freedom in the design first — a silhouette that is not in the catalogue, a mechanism assembled differently, a proportion tried for the first time. Then freedom in the materials: a distinctive wood, a particular steel, a decoration that requires its own time.

That freedom has a concrete counterpart. Preparation, trials and rework cannot be spread over anything else. If an adjustment takes three attempts, all three belong to that one knife. More advanced finishes, details reworked, time spent on filework or polishing: it all accumulates on a single piece.

A one-off piece is made entirely in the workshop, from design to final inspection. It is also my research space: the shapes and technical solutions I explore there later feed into series models. Many of these pieces come from my own ideas rather than a commission — you can see the exceptional pieces currently available or browse the workshop's past work to get an idea of the results.

Comparison table: small series or one-off piece

Comparison between a FL Toussaint small-series knife and a one-off piece
Criterion Small series One-off piece
Design Proven model, refined from series to series Specific design created for this piece alone
Number of pieces Several coherent examples A single example
Preparation Shared across the batch and spread over several pieces Borne entirely by one piece
Choice of materials Selection defined for the series Distinctive materials possible, including difficult ones to work
Available variants A few options planned in advance Not applicable: the piece is its own version
Level of finish Matches the level defined for the range More advanced finishes and more extensively worked details
Consistency between examples Sought through templates and procedures Not applicable: every choice is specific to the piece
Manufacturing time Optimised through batch work Specific time, trials and rework that cannot be shared
Availability Depends on current series and announced drops Depends on pieces available or in preparation
Price More contained: preparation cost spread over several pieces Higher: design and development borne by a single piece
Recommended use Regular use, first handmade knife, gift Attachment to a design or material, milestone in a collection
Character of the piece Recognisable model, coherent examples A piece that will not be reproduced identically

What is actually done in the workshop

It is worth stating clearly, because few makers do.

For a one-off piece

A one-off piece is made entirely in the workshop in Courpière. Design, manufacture, fitting, finishing, sharpening and inspection: everything passes through my hands. That does not mean working without machines — I design my cutting files and operate the laser cutter myself — but no operation is entrusted to a third party.

For a small series

On series models, two operations may be entrusted to professional partners in the Thiers basin depending on how the batch is organised: heat treatment, meaning hardening, and grinding. This is not systematic. When it is done, it makes it possible to produce a coherent batch while entrusting specialised or repetitive operations to professionals who perform them every day.

I remain directly responsible for design, preparation and verification of components, fitting, assembly, rework, finishing, sharpening and final inspection. In other words, the design of the knife and the result you hold in your hand. For details of the operations, you can discover the stages involved in making a handmade knife.

Why a small series can cost less

Not because it is made less well. Because it is better organised.

Prototyping, templates and settings: all this upstream work has already been paid for by previous series, or is spread over the current batch. When I prepare ten blades instead of one, every tooling change, every machine setting and every material purchase benefits ten knives. Unproductive time — searching, setting up, starting again — is mechanically reduced.

A series also limits unnecessary variations. Materials are chosen and prepared for the whole batch. Procedures are repeated and therefore refined. A small series must reach the level of quality defined for its range: the mechanism is adjusted, the edge is sharpened and final inspection is applied to every example, exactly as with the rest of my production.

It is this organisation that makes a handmade knife accessible to a wider budget. To see how this translates in practice, you can understand the price of a handmade knife.

What drives up the price of a one-off piece

On a one-off piece, nothing is shared. The specific design takes time to draw and develop. Special components are made individually. Trials and rework belong to that one piece.

Then there are difficult materials: certain woods, composites and steels require precautions, dedicated tools and sometimes several attempts. Advanced finishes and any decorative work — polishing, filework, assembly details — are counted in hours, not minutes.

One point matters: an expensive material does not make a good knife. It catches the eye; it does not replace fitting, geometry or the knife you actually need. The price of a one-off piece pays above all for working and design time, not rarity alone.

Which knife should you choose according to your priority?

Choose a small series when…

  • the knife is meant to be used regularly — slicing sausage at a snack, opening parcels, working in the kitchen;
  • the model you like is already identified in the catalogue;
  • the budget needs to remain controlled without giving up handmade production;
  • availability matters: a series exists or a drop has been announced;
  • the planned variants suit your taste;
  • you are looking for a first handmade knife or a durable gift, without entering into a complex commission.

Choose a one-off piece when…

  • the design or material is central to what you want;
  • you want a piece that will not be reproduced identically;
  • finishes and details matter more than lead time;
  • you accept the time required to make it;
  • the piece is intended to mark a milestone in a collection;
  • you are looking for a piece already designed by the maker rather than a catalogue of variants.

When either option could work

If you are still hesitating, go through the criteria in this order: use first, then the shape of the knife, then the mechanism or blade geometry, the maintenance you are willing to do, the budget, and finally aesthetic expectations. A simple knife chosen well will be more useful than an ambitious piece poorly suited to what you will do with it. If use points toward a series model and desire toward a one-off piece, there is nothing stopping you from starting with one and keeping the other for later. A cheese board will not wait.

The same requirements, different levels of work

Series or one-off piece, the fundamentals do not change. Mechanism safety, fitting, geometry and the edge are not optional: every knife leaving the workshop is inspected and sharpened, whatever its price.

What varies is the time devoted to each piece, freedom of design, rarity, materials and level of finish. A small series allows more people to access a knife designed and finished by a maker in the Thiers basin. The one-off piece preserves the space for research and freedom without which this trade would go round in circles.

Frequently asked questions

Is a small series still artisanal?
Yes. Batch work organizes the preparation, but each knife remains adjusted, assembled, sharpened and checked individually in the workshop. The series is based on a model that I designed, prototyped and refined myself. What changes compared to a single piece is the distribution of the preparation time over several examples — not the nature of the work on each knife.
Is a unique piece necessarily of better quality?
No. The functional requirements – mechanism, adjustments, geometry, cutting edge – apply to all my production. A unique piece receives more time, unique materials and more advanced finishes, but a well-chosen series knife can better meet your use than an ambitious piece that is poorly adapted. Quality is first judged by the suitability between the knife and what you do with it.
why can a small series be more accessible?
Because fixed costs are distributed. Prototyping, jigs, machine setups and material preparation serve multiple knives instead of just one. Consolidated operations reduce tooling changes and downtime. The price falls by organization, not by simplification of the knife: the level of quality defined for the range remains the same on each copy.
What operations can be entrusted to partners?
Only on series models, and only two operations: heat treatment (quenching) and grinding. It’s not systematic — it depends on the series and its organization. The design, preparation of components, adjustment, assembly, rework, finishing, sharpening and final inspection remain carried out in the workshop, for each knife.
Is a unique FL Toussaint piece entirely made in the workshop?
Yes, completely, from design to final inspection. No operation is entrusted to a third party on a single piece. This does not exclude the use of machines: I design my cutting files and I carry out the laser cutting myself, as with the rest of my production. The difference lies in the scope: everything happens in my hands, at Courpière.
Can we personalize a small series knife?
It depends on the model and series. Some series provide for variations in materials or finishes, defined in advance; others are offered in a single configuration. The exact possibilities appear on the sheet for each series or each product. I do not offer non-catalog modifications on series models: that is the role of unique pieces.
Is a unique piece suitable for everyday use?
It can be: my knives are designed to be used, including unique pieces. The point to check concerns the materials and finishes chosen - some require more attention to maintenance than a standard model designed for intensive use. If the knife must be used every day without special precautions, say so: this guides the choice of materials.
How to choose for a gift?
Start from the person, not the object. For someone who will use their knife - kitchen, table, pocket - a standard model is a safe choice: available, proven, at a controlled budget. For an informed enthusiast or a collector, a unique piece or an already available creation makes a bigger impact. If in doubt, the regularity of a production model can rarely be faulted.
Is a small series necessarily numbered?
No, not necessarily. The numbering depends on the series concerned: certain limited series or certain drops may be, others not. The information appears on the series or product sheet when it applies. Numbering is not an indicator of quality in any case — it simply documents the place of a copy in a defined lot.
Back to top